Connect a mailbox
- Open Personal settings → Connected Accounts and find the Email card.
- Click Connect E-Mail, then Start E-Mail connection. The connection opens in a new tab, so allow pop-ups in your browser.
- Sign in with Google, Outlook, or another provider via IMAP.
Your first mailbox is marked Primary; further ones are Secondary. A working mailbox shows "Sending and reply tracking active." If it shows Logged out, sending from it has stopped: click Reconnect. The sidebar also warns you when mailboxes are logged out.
Mailbox settings and the daily limit
Click Edit email settings next to a mailbox to set:
- Sender First Name and Sender Last Name
- Limit per day: how many emails this mailbox sends per day, between 1 and 500. The default is 20.
- E-Mail Signature, with Send Test Email to check it. Whether Signalist adds the signature to your emails is set under Copywriting → General → Email Signature; see Add your email signature to emails.
The limit applies per mailbox. Emails beyond it wait for the next sending window. Start low and raise it slowly while replies and bounces stay healthy.
When emails go out
- Sending window: each campaign has a time zone and sending times per weekday, set in the campaign's Schedule section. Emails only go out inside that window; outside it, they wait for the next one.
- Spacing: Signalist spreads a mailbox's emails over the window, with between 30 seconds and 5 minutes between two emails.
- Delays between steps: set per step in the campaign builder ("after N days", 0 to 30). A step you add starts with the delay from Copywriting → General → Send Delay Defaults for its step number, or 1 day if none is set. The first step of a campaign goes out in the next sending window.
- Several senders: a lead's first step goes to one of the campaign's active senders, chosen at random among those with room left that day. Follow-ups come from the same sender.
A message under Scheduled in the Outbox is planned, not stuck.
Finding email addresses
A list decides when Signalist looks up email addresses, in its settings under Find contact information like email phone number and company phone number:
- right before the lead's first email step, or at a Has email condition in the campaign (the default)
- for all leads when the list runs
- when the lead is assigned to a campaign
A lookup costs 1 credit and is charged only when an address is found. Not every lead has a findable address; the Outbox then shows the step as skipped.
Bounces and unsubscribes
- Bounces: once an email to an address hard-bounces, Signalist puts the address on your workspace's suppression list (Do Not Contact → Suppressed) and does not email it again. The next email step shows "… skipped" in the Outbox, and the campaign continues with its next step. If you have a working address for the lead, add it to the lead's contact info, or reach them on LinkedIn. If the address works after all, you can remove it from Suppressed.
- Unsubscribe link: add the Unsubscribe Link variable to your emails. A lead who clicks it is added to your blacklist and is not contacted again.
Open and click tracking
The campaign settings offer Track E-Mail Openings and Track Clicks. Both are off by default and marked "Not recommended": tracking pixels and rewritten links make emails look less personal to spam filters and can hurt deliverability.
Troubleshooting
| Problem | What to check |
|---|
| Emails are sent later than expected | The campaign's sending window and time zone, the mailbox's Limit per day, and the step delay. |
| Nothing is sent from a mailbox | The mailbox may be Logged out. Reconnect it under Personal settings → Connected Accounts. |
| A lead has no email | The lookup found no address. Enrich the lead, or reach them on LinkedIn. |
| Bounces increase | Lower the daily limit and check the quality of your lists. Hard-bounced addresses are suppressed and skipped automatically. |
| Emails go out without your signature | Check that the mailbox has an E-Mail Signature and that Email Signature is switched on under Copywriting → General. |
Frequently asked questions
What is a safe daily limit?
The default of 20 per mailbox is a sensible start. Raise it slowly, and only while bounces stay low and replies come in.
Can I spread sending over several mailboxes?
Yes. Connect additional mailboxes and add their users as senders to the campaign. Each mailbox has its own daily limit.
Why is a step "Scheduled" but not sent yet?
It is waiting for the sending window, the mailbox's daily limit, or the step's delay. It goes out automatically.
Does Signalist email a bounced address again?
No, not on its own. It depends on the kind of bounce:
- Hard bounce, or a bounce Signalist cannot classify: the address goes on your Suppressed list (Do Not Contact → Suppressed), and further emails to it are skipped until you remove it there.
- Soft bounce (for example a full mailbox or a temporary refusal): Signalist retries that one email step once, at the earliest a day later, inside the campaign's sending window. If the retry bounces too, nothing more is sent for that step. The address is not suppressed. A step is not retried if it is the campaign's last email step, or if the lead has replied or been stopped.
- Block by the receiving server: only the email step that bounced is marked as failed. It is not retried, and the address is not suppressed.
Should I switch on open tracking?
Usually not. It can hurt deliverability. Replies are a more reliable signal.